Machine safety: Confusion amuck, quantitative circuit design versus qualitative risk assessment

When talking about qualitative versus quantitative as they relate to machine safety standards and compliance requirements, are we talking about the risk assessment process? Or do we consider the process to engineer and mitigate hazards related to the Safety Related Parts of Control System (SRP/CS)?

11/13/2012


Is everyone confused about the terms qualitative versus quantitative as they relate to machine safety standards and compliance requirements? Weekly we hear the entire industry talking about the transition from qualitative to quantitative hazard analysis and mitigation. Is anyone confused as to whether we're talking about the risk assessment process or the process to engineer and mitigate hazards related to the Safety Related Parts of Control System (SRP/CS)? Wow – that’s a mouth full!

The relatively new machine safety standard that brings this question to the front of discussion is – ISO 13849-1:2006. A big hint to resolve this question is on the cover page. The title of this standard is – Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design. Now, having said this, the entire international standard is focused on the design and integration effort. Paragraph 1 of clause 1 reads:

1    Scope

This part of ISO 13849 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SRP/CS), including the design of software. For these parts of SRP/CS, it specifies characteristics that include the performance level required for carrying out safety functions. It applies to SRP/CS, regardless of the type of technology and energy used (electrical, hydraulic, pneumatic, mechanical, etc.), for all kinds of machinery.

Based on the above paragraph isn’t it positively clear that this standard is directed at the design and integration of the SRP/CS including the design of software. Yes, this standard moves these efforts and compliance requirements into the realm of quantitatively designing safety-related circuits introducing such terms as Performance Level (PL) and much more. In the past, engineers and maintenance personnel used the qualitative approaches brought forward in 1996 by EN 954-1. I don’t believe that further definition is needed at this point to establish a direct correlation between quantitative and the design requirements for compliance to ISO 13849-1. Trust me, if more details are needed they abound in the four day courses being offered for designers.

On the other hand, is there any direct correlation of quantitative approaches to the risk assessment process? In my opinion, I don’t believe there is any direct correlation. To be brief, I suggest that the risk assessment process is an entirely separate process by which the intended use of the machine, the tasks and hazards, and the level of risk(s) are determined. Within the risk assessment process (for machines in design & legacy machines) it is required that identified hazards must be analyzed and reduced to an acceptable (residual) risk. There are five steps commonly recommended for this effort called the “Hierarchy of Measures” which can be used for the hazard mitigation plan. The implementation of the hazard mitigation plans is completed via design engineering. Most of the available risk assessment approaches use a three factor system for scoring the risk of a hazard - frequency, severity and likelihood. And, this is a qualitative scoring process – not quantitative!

Do you agree that engineering the solution (both new & legacy machines) under ISO 13849-1:2006 is quantitative but not the risk assessment?

Your comments or suggestion are always welcome so please let us know your thoughts. Submit your ideas, experiences, and challenges on this subject in the comments section below. Click on the following text if you don't see a comments box, then scroll down: Machine safety: Confusion amuck, quantitative circuit design versus qualitative risk assessment.

J.B. Titus, CFSERelated articles:

Machine Safety – does a risk assessment need to be updated for a minor modification to a machine?

Machine Guarding & The Hierarchy of Measures for Hazard Mitigation

Machine Safety – does OSHA reference consensus standards for compliance?

Machine Safety: Is OSHA okay with my 'acceptable' risk mitigation?

Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
Water use efficiency: Diminishing water quality, escalating costs; Lowering building energy use; Power for fire pumps
Building envelope and integration; Manufacturing industrial Q&A; NFPA 99; Testing fire systems
Labs and research facilities: Q&A with the experts; Water heating systems; Smart building integration; 40 Under 40 winners
Maintaining low data center PUE; Using eco mode in UPS systems; Commissioning electrical and power systems; Exploring dc power distribution alternatives
Protecting standby generators for mission critical facilities; Selecting energy-efficient transformers; Integrating power monitoring systems; Mitigating harmonics in electrical systems
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.