Defining NFPA 37

NFPA 37 outlines the minimum fire safety requirements for the installation and operation of permanently installed engines including stationary, engine-driven equipment.


This article is peer-reviewed.Learning Objectives:

  • Analyze NFPA 37 and its implications for designing stationary, engine-driven equipment such as generator systems.
  • Illustrate how to design fuel systems for gensets.
  • Show how NFPA 37 affects fire and life safety systems in buildings.

NFPA 37: Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines, 2015 edition, is an important yet often overlooked player in NFPA's extensive lineup of codes and standards. The stated purpose of the document is to provide "minimum fire-safety requirements for the installation and operation" of permanently installed engines.

The origins of NFPA 37 trace back to 1905, where it was published by the National Board of Fire Underwriters, and subsequent versions were published originally by the NFPA technical Committee on Explosives and Combustibles and currently by the NFPA Technical Committee on Internal Combustion Engines.

That history becomes important when looking at what NFPA 37 is—and what it isn't. NFPA 37 was a project originated by Fire Underwriters with the main goal of creating a standard set of installation, operation, and maintenance criteria to minimize the likelihood of fire caused by fuel-fired engines inside of or adjacent to structures. While NFPA 37's requirements are most often applied to generators, the scope of the standard applies to all stationary, engine-driven equipment. The scope of NFPA 37 does overlap with other sections, such as:

NFPA 110 and the NEC (specifically generator-specific Articles 700, 701, 702, and 708) serve to create a baseline for the electrical integrity, reliability, and operation of emergency systems. NFPA 37 primarily is concerned with making sure the engine itself and its associated components (fuel supply, fuel tanks, environment, etc.) are not installed in a manner that creates a potential fire hazard. NFPA 37 is not concerned with the electrical distribution system fed from a generator or the maintenance protocol to ensure that the emergency system is available when needed; instead, the standard ensures that the engine itself does not pose a threat or hazard to the structures around it.

The goal of NFPA 37 is to provide a roadmap for safe installation which, if followed, will function to not only minimize the likelihood of a fire but also then contain the spread of a fire if required.

  • Location, construction, and installation requirements serve to prevent a fire in the engine from spreading to adjacent spaces or structures.
  • Ventilation requirements keep the equipment space from overheating, compromising wiring or the engine itself, as well as preventing buildup of combustible fumes, which could otherwise ignite or cause explosion.
  • Requirements for fuel piping provide installation, material, and equipment guidelines that ensure clean, reliable distribution of fuel to the engine.
  • Automatic-shutoff requirements are designed to automatically cut off flow of fuel to an engine when it is not running or running under abnormal operating conditions. In addition, requirements for manual, remote shutoffs allow maintenance staff or first responders to disable the unit without having to physically approach it or enter a space in which there may be a dangerous event.
  • On-site fuel-storage requirements serve to minimize potential for spills, overfilling, and leaks from fuel tanks and the engine itself. Tank size limits in conjunction with location and construction regulations help minimize the ability of an active fire to spread.
  • Other requirements found within the standard include wiring methods, mandatory controls, and exhaust requirements. 

While the purpose of this article is to highlight significant requirements for commercial emergency and standby generator installations, it's important to remember that NFPA 37 applies to all stationary engines and turbines, both residential and commercial installations. Refer to the full standard for additional requirements for those applications.

Locations and installation

NFPA 37 identifies four separate categories for generator locations:

  • Dedicated rooms within a building
  • Dedicated detached structures adjacent to a building
  • Exposed on the roof of a structure
  • Outdoors.

While this particular code does not dictate whether an engine located within a building needs to be installed in a separate room, Section 4.1.2 provides requirements of the room for when it is. (Note that in the case of an emergency generator, a separate room is required by NFPA 110, Section 7.2.) NFPA 37-2015 Section 4.1.2 notes that an engine room within a structure must have walls, floors, and ceilings that are 1-hr rated, the only exception being the ceiling of a room on the top floor of a building can be noncombustible or protected with an automatic fire protection system.

Figure 1: Shown is the required minimum separation for outdoor and rooftop-mounted engines. Courtesy: Barton AssociatesThe standard also provides requirements for installations on building roofs and outdoor installations. In both cases, the minimum separation distance from the engine housing is 5 ft to any opening in an adjacent building and 5 ft to any structure with combustible walls, building openings, overhangs, and vegetation. There are two listed exceptions to the minimum distance (see Figure 1):

Exception 1: When the adjacent wall or structure has a fire rating of at least 1 hr.

Exception 2: When the weatherproof generator enclosure is "constructed of noncombustible materials and it has been demonstrated that a fire within the enclosure will not ignite combustible materials outside the enclosure."

Exception 2 is easily the most frequently discussed and debated requirement in the entire standard. There have been formal interpretations, proposed amendments, and public comments on the topic. Many manufacturers have enlisted third-party testing agencies to show that their units meet the requirements of Exception 2, and, therefore, can be installed closer than 5 ft from adjacent structures. As currently written, there are no specific parameters given for the actual enclosure fire test.

This often leaves room for interpretation. For example, what is the exterior cladding of the adjacent structure? Different materials have different combustion profiles. Is the generator running or not running during the test? Research has shown that in an air-cooled unit, when running, the fan can serve to extinguish a fire within the enclosure sooner than if it were not operational at the time.

Authorities having jurisdiction (AHJs) have argued that currently there are no provisions for an inspector or reviewer to reject "proof" from a manufacturer that a particular enclosure meets the second exception. In order to assure safety, it is recommended that a system installer maintain the 5-ft separation wherever possible and only rely on the exceptions when absolutely necessary for a particular installation.

Figure 2: Engineers can use this example as the required minimum separation for dedicated engine structures. Courtesy: Barton AssociatesIn the case of a generator that is installed in a dedicated detached structure, such as an equipment out-building, those installations have similar requirements to those listed above with a minimum separation of 5 ft from the structure (not the engine) to an adjacent building. For dedicated structures, the minimum requirement is superseded when either the outbuilding or the adjacent wall are 1-hr rated, or when the outbuilding has an automatic fire-suppression system (see Figure 2). Note that if a project is designed to meet the NFPA 110 requirement for all generators within a building to be located in a rated room, the installation inherently qualifies for Exception 2.

Other notable requirements concern ventilation and storage in the engine space. Engine rooms and structures are required to have dedicated ventilation systems sized adequately to meet combustion requirements of the engine and prevent buildup of fumes and products of combustion in the space. Storage of combustible materials other than those required for day-to-day operation (manuals, filters, etc.) is strictly prohibited.

<< First < Previous Page 1 Page 2 Next > Last >>

Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
How to use IPD; 2017 Commissioning Giants; CFDs and harmonic mitigation; Eight steps to determine plumbing system requirements
2017 MEP Giants; Mergers and acquisitions report; ASHRAE 62.1; LEED v4 updates and tips; Understanding overcurrent protection
Integrating electrical and HVAC for energy efficiency; Mixed-use buildings; ASHRAE 90.4; Wireless fire alarms assessment and challenges
Power system design for high-performance buildings; mitigating arc flash hazards
Transformers; Electrical system design; Selecting and sizing transformers; Grounded and ungrounded system design, Paralleling generator systems
Commissioning electrical systems; Designing emergency and standby generator systems; VFDs in high-performance buildings
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me