Examining government, state, municipal, federal, and military facilities: HVAC

Government and military projects are among the toughest challenges an engineer can face. Demanding facility owners, tight budget limitations, safety concerns, and other factors all come into play. Here, engineers with experience in the field offer advice on how to succeed in regards to HVAC.

07/17/2018


Top row: Roger Chang, Shem Heiple. Bottom row: Dalrio Lewis, Spencer Morgenthau. Courtesy: DLR Group, Interface Engineering, RTM Associates, Southland IndustriesRespondents

  • Roger Chang, PE, LEED Fellow, Principal, DLR Group, Washington, D.C.
  • Shem Heiple, PE, LEED AP, Associate Principal, Senior Mechanical Engineer, Interface Engineering, Portland, Ore.
  • Dalrio Lewis, PE, Project Engineer, RTM Associates, Orlando, Fla.
  • Spencer Morgenthau, CPSM, LEED AP, Director of Business Development, Southland Energy, a division of Southland Industries, Sterling, Va.

 


CSE: What unique heating and cooling systems have you specified in such projects? Describe a difficult climate in which you designed an HVAC system.

Chang: We are seeing significant interest in ground-source heating and cooling systems, which can be adapted to a wide range of climates but require a clear understanding of ground properties and a building's heating- and cooling-load balance. The increasing adoption of heat pump technology is tied to the benefits of electrification, as utility-grid-delivered electricity is made up of a higher percentage of renewable sources.

Heiple: We recently designed a facility in Niger with outdoor-air temperatures exceeding 120°F, frequent dust storms, and unreliable water and power utilities. Extensive load and energy analysis was conducted to provide design guidance on HVAC system performance integration with the building envelope. We used inertial filtration and sand louvers to address dust and indoor-air quality. Due to the dry air during continuous hot conditions, humidification was beneficial to maintain expected low humidity levels that also provided significant energy savings.

Spanning 5.4 million sq ft, the Fort Riley facility improvements in Kansas include upgrading the central plants and energy-management controls; HVAC upgrades; LED lighting; and boiler and water-conservation. Courtesy: Southland IndustriesCSE: What unusual or infrequently specified products or systems did you use to meet challenging HVAC needs?

Heiple: We recently designed a courtroom building with diverse space requirements that used active chilled beams and displacement ventilation with thermally activated slabs to meet energy goals and comfort requirements.

Chang: We are seeing a continued move to the use of dedicated outdoor air systems (DOAS) where ventilation-air delivery is decoupled from space heating and cooling. This requires additional care to meet the economizer provisions in the IECC/ASHRAE 90.1. The increasing use of distributed VRV fan coil units and fan-powered VAV boxes with cooling comes with a challenge of decentralized filter-change requirements. We have included polarized media-type filters on a major government project to decrease filter-change intervals.

CSE: What types of air economizers or other strategies are owners and facility managers requesting in government, state, municipal, federal, and military facilities?

Heiple: Recently, DOAS have gained acceptance in many government design standards. The major energy efficiency advantage to these systems is the ability to use air-to-air heat recovery, but the trade-off is that they are not capable of providing full economization because they are typically not sized to provide outside air rates exceeding minimum ventilation standards. For some projects, and depending on the climate, we have proven through analysis that full air-side economizer systems are more beneficial for energy conservation and indoor air quality than dedicated outside air systems, and we were allowed an exception to the design standards.

CSE: How have you worked with HVAC system or equipment design to increase the building's energy efficiency?

Chang: Design assumptions for process load have a significant impact on zone-level heating and cooling system design, especially given increasing stringency for building envelope and lighting performance. While process-load density has dropped significantly in the past decade, due to increasing use of LED monitors and laptops, the unpredictability of process loads results in the use of prescriptive assumptions. Early and frequent dialog on assumptions allows better sizing of equipment, which allows improved fit, reduced first-cost investment, and better performance at low and part-load demand.



Product of the Year
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
40 Under Forty: Get Recognized
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
MEP Giants Program
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
October 2018
Approaches to building engineering, 2018 Commissioning Giants, integrated project delivery, improving construction efficiency, an IPD primer, collaborative projects, NFPA 13 sprinkler systems.
September 2018
Power boiler control, Product of the Year, power generation,and integration and interoperability
August 2018
MEP Giants, lighting designs, circuit protection, ventilation systems, and more
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
click me