School's BAS controls lights, HVAC

An elementary school’s new BAS combined HVAC and lighting controls provide wireless capabilities and lower costs.

06/29/2011


I recently visited an elementary school with a brand new BAS. Before the installation, the building had absolutely no HVAC or lighting controls. The entire school was heated at the same time in winter, regardless of classroom occupation. Each room was either completely lit or not at all, with no in-between. Remotely shutting off the lights at the end of the day or preheating some rooms in the morning if the night had been cold was not manageable. In short, the school needed fully programmable lighting and HVAC control with the best payback period possible.

For this project, the school opted for the solution offering the best control-to-price ratio: a system that merged HVAC and lighting management using single controllers with wireless capabilities.

For the two main floors of the school, 31 actuators, 29 thermostats, 59 light switches, and 57 light relays are controlled by only 9 controllers (CAN2GO wired and wireless controllers). All of the end-devices communicate with the controllers wirelessly; I/O wiring was not needed. The installation was not impeded or made more expensive because of controller I/O counts or separate HVAC and lighting control hardware. Each controller manages a variety of HVAC and lighting end-devices without the help of any gateway. The controllers convert each point into BACnet objects for seamless integration into a number of building management systems (BMS).

In addition to the hardware and scalability savings, the electrical labor cost of the installation was reduced by 61% as none of the walls or ceilings were opened to connect end-devices to controllers. In this project, the networking between controllers was also done wirelessly, increasing the savings on labor and repair work. The only wiring in this project was to connect one controller to the local area network (LAN) and connect the nine controllers to their respective power source. The rest—networking and control—was all wireless.

By avoiding wiring when possible, contractors and end users were protected from stumbling upon hazards hiding inside the walls. Less renovation work also meant less downtime—a key pain point in many building automation installations and retrofits.

Figure 1: A single controller can use several wireless protocols (EnOcean for end-devices, ZigBee for networking) to manage multiple applications. Courtesy:  SCL Elements Inc./CAN2GO

I have asked many contractors how they would have proceeded without such technology. For HVAC control, most of them would have used 31 controllers because there are 31 actuators. For lighting control, many didn’t know how they would have proceeded without blowing up the costs—incurring a double-digit payback period, mostly due to added electrical labor and controller costs.

With the HVAC and lighting controls merged into one unit, the only labor required to add lighting control was to insert wireless relays into the ballasts and to place wireless switches in the classroom. The controllers did the rest.

Figure 2: Zooming in on one part of the elementary school shows one controller wirelessly managing HVAC and lighting end-devices for several classrooms, a hallway, and a stairway. Courtesy:  SCL Elements Inc./CAN2GO

The BMS is managed by the school board’s technical staff and a hired consultant. They are in charge of programming the controllers according to school schedules. Each controller is equipped with a real-time clock and has local storage, making the controllers both autonomous and available from a centralized interface.

Changes to the programming are made remotely. The updates are sent to the controllers via a secure access to the LAN and are then pushed, from unit to unit, via the wireless ZigBee mesh network. There is no need to visit the school to make changes to the system.

Hamer is the vice president of Product Strategy at SCL Elements Inc. He is the co-founder of the engineering consulting firm Eco2Max and has worked for Nortel and Verint. His expertise covers energy efficiency, greenhouse gas reduction, wireless technologies, and network reliability and security.



No comments
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
High-performance buildings; Building envelope and integration; Electrical, HVAC system integration; Smoke control systems; Using BAS for M&V
Pressure piping systems: Designing with ASME; Lab ventilation; Lighting controls; Reduce energy use with VFDs
Smoke control: Designing for proper ventilation; Smart Grid Standard 201P; Commissioning HVAC systems; Boilers and boiler systems
Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Consulting-Specifying Engineer case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.

Protecting standby generators for mission critical facilities; Selecting energy-efficient transformers; Integrating power monitoring systems; Mitigating harmonics in electrical systems
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software
Integrating BAS, electrical systems; Electrical system flexibility; Hospital electrical distribution; Electrical system grounding
Cannon Design’s blog is a place for the many voices of the firm to share thoughts and news related to current projects...
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.