Green power roundtable: Exploring green impacts of electrical distribution systems

06/13/2013


Q: What electrical system reliability issues have you seen, and how are your technologies addressing these? 

Loucks: Switching inductive loads can produce voltage transients, which are initiated whenever there is a sudden change of circuit conditions. We have seen situations where dry-type transformers have been damaged due to switching transients. These switching transients produce both steep-front wave and end-of-turn damage to transformers and motors, but they also excite resonances that occur within a core-and-coil assembly of a motor or transformer. A transient voltage study is highly effective at identifying the corrective measures that are required to avoid system downtime and equipment damage. Typical corrective measures include surge arrestors, damping resistor-capacitor combinations, and modified switching resistors. 

Powell: Power outages are occurring more frequently than ever and lasting longer with devastating effects. Siemens standby generators protect homes and businesses from unpredictable weather and unforeseen outages. They are available from 8 kW to 150 kW and are powerful enough to back entire homes or businesses without the cost of an expensive configured system.

Smith: When powering equipment from dc with a direct connection to a backup battery, failures in the upstream ac generation and distribution network do not impact the critical load for a period of time dictated by the capacity of the battery system. Additional isolation from electronic failures is provided by provisioning redundant elements in the system architecture. Multiple redundant battery strings are employed to protect from battery element failures. The same redundant approach is taken in renewable energy systems, with multiple solar panel strings being used to feed the dc storage bus and battery elements through independent converters. 

Walker: CES attacks reliability issues head-on and results in a new paradigm for level of service. The CES units are deployed near the customer and contain an energy reserve for reliability. If a facility outage occurs, the storage unit immediately isolates from the grid and continues to supply the local customers. The interruption can be avoided altogether as long as the grid is returned to service within a few hours. Even the momentary interruptions typically associated with a line sectionalizing event are avoided due to the immediate transfer of load from the utility system to the energy storage battery system. 

Q: What impacts are green power sources having on system reliability, and how is your company addressing these issues? 

Loucks: There is voltage imbalance due to variable single-phase distributed generation. But even 3-phase distributed generation is causing issues. The Texas Competitive Renewable Energy Zone project is adding 20 GW of wind from West Texas and the Panhandle to highly populated metropolitan areas of the state. Due to the variable nature of renewable energy and to reduce flicker, substantial additional power electronic hardware is being added. 

As the percentage of renewable power increases, grid stability is reduced. A solution is to provide more transmission interconnects to distribute sources and loads over larger areas. However, there is a lot of resistance to building more towers where people live, work, and play (and rely on electrical power to do so). To address these issues, Eaton is working with energy storage solutions that mitigate fluctuations due to the variable nature of renewable energy. Integrated, grid-tied storage is helping to make renewable energy a dependable, on-demand power that is deliverable with controllable power ramp rates.

Powell: Renewable energy can be hard to control because it generates power intermittently. However, our control systems—together with storage—minimize the adverse impact arising out of these on the micro grid as well as the macro grid. 

Smith: Many sources of green power, such as solar and wind, are inherently intermittent. The traditional architecture of a dc power system with battery backup provides protection from the intermittent absence of the green source by storing backup energy for use during these times. Proper understanding of the availability of the sources, combined with appropriate provisioning of the power generating elements, sizing of the storage battery, and provisioning alternative or backup sources, allows for maximum reliability and minimum cost to be achieved. 

Walker: One of the concerns of highly distributed, small solar generators is their power output fluctuation, which results from rapidly varying sunlight. The power output variations of solar generators across a distribution feeder are tightly synchronized, causing voltage swings that are faster than traditional voltage regulation can compensate. CES units that are deployed in the same area will provide the necessary compensation to stabilize voltage. The CES units operate in four quadrants, which are defined as real and reactive power both in and out. They can be configured to perform power smoothing where real power is exchanged, stored, or released to compensate solar generator output variations. The CES units also consume or produce reactive power as required to directly control local voltage magnitude swings. 



No comments
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
2014 Product of the Year finalists: Vote now; Boiler systems; Indirect cooling; Integrating lighting, HVAC
High-performance buildings; Building envelope and integration; Electrical, HVAC system integration; Smoke control systems; Using BAS for M&V
Pressure piping systems: Designing with ASME; Lab ventilation; Lighting controls; Reduce energy use with VFDs
Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Consulting-Specifying Engineer case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.

Protecting standby generators for mission critical facilities; Selecting energy-efficient transformers; Integrating power monitoring systems; Mitigating harmonics in electrical systems
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software
Integrating BAS, electrical systems; Electrical system flexibility; Hospital electrical distribution; Electrical system grounding
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.