PCs, Flowcharts, and SDS Speed Production at Silicon Graphics

Smart Distributed System

02/01/1997


F or Ron Stone, applications manager for FloStor Engineering in Hayward, Calif., Honeywell's Smart Distributed System (SDS) proved to be the answer to a two-year search. FloStor, a leading materials handling integrator in Northern California, serves companies that manufacture and distribute products from computers to automobiles.

rkstations, approached FloStor with a request for just such a system--and with a very tight deadline.

 

rther work or testing.

at it will be much easier to accommodate those changes in the flowchart environment compared to configuration of the control network.

Faster than a PLC

The Smart Distributed System sped the installation process at SGI by allowing FloStor engineers to simplify the control programming, bring the system online, and quickly debug it. While the older PLC system provided some of these features, Mr. Stone says the Honeywell PC system gives his SGI customers much more control over the process.

ation--not cost--was the critical factor.

rather than interfacing with I/O boards and trying to use less expensive but unintelligent devices.' Using I/O boards means lost diagnostic capability--a major issue--in addition to exposing the installer to other problems which are much more difficult to uncover and address.

Adaptability a key

SDS is an ideal match for many of FloStor's Silicon Valley customers who have constantly evolving product lines and need to get their production running as quickly as possible. In the initial stages of many projects, FloStor usually lacks a complete set of specifications and makes constant modifications as it brings a project up to speed. 'Silicon Graphics doesn't know exactly how it is going to use the line,' says Mr. Stone. 'So our task is to provide the flexibility that allows SGI to move product around as its needs evolve.'

 

 


SDS At a Glance

S mart Distributed System (SDS) was introduced by Honeywell Micro Switch in early 1993 and formally opened to other vendors the following year. SDS nodes are built on CAN (Control Area Network) chips, which were developed for the automobile industry.

lower transmission speeds. SDS does not lend itself to repeaters. If many nodes and long distances are needed, SDS could be fed into another higher level bus. Significant branching could also be achieved with active hubs.

ess information at burst speed (maximum message rate) without dropping messages. When this is accomplished SDS can be the most efficient network because it reports only changes at the nodes. The user must decide if the loss of an attendance check on every scan (attendance polling) is acceptable.

www.turck.com


PC Control for the Factory Floor--It's Here to Stay

A s we look to the year 2000, there's an exciting future in store for manufacturing. 'Technology threads' are converging on the factory floor, and as they meet, users will find unparalleled productivity gains. Those technology 'threads' are PC control, device-level networks, and smart devices.

a robust, open, device-level network.

 

 

 

 

r material handling equipment to packaging equipment, canning lines, and automotive assembly lines--harsh environments where speed, flexibility, and maximum uptime are critical.

 

igence resides in the field devices, thus redefining the function of host controllers, PCs or otherwise.

--Steve Glaze, Honeywell Micro Switch


Power devices on SDS

GELink MC, as part of a completely integrated control system incorporating SDS and GE Fanuc Series 90/30 PLC SDS interface modules, provides users with the ability to connect power devices such as contactors, motor starters, and circuit breakers to a real-time control network. Four 10 A outputs and four discrete inputs can be handled.

GE ELECTRICAL DISTRIBUTION & CONTROL

Adjustable-frequency drive

This new serial communication option makes it possible to completely control and diagnose the AF-300 Micro $aver adjustable-frequency drive from the SDS bus. The Micro $aver drive is available for 230 V ac (single and three-phase) and 460 V ac input with ratings from 0.25 to 5 hp.

GE MOTORS &
INDUSTRIAL SYSTEMS

Analog I/O for SDS

This module supports up to four analog inputs or outputs as a single bus load. Each 12-bit analog channel uses one bus address and has an average update time of 8 msec per channel. The analog circuitry requires a 10-30 V dc power source.

HOLJERON

Multipurpose valves

The Mark 4 manifold is a multipurpose 4-way valve, 2- and 3-position, which incorporates the manufacturer's reliable spool and sleeve valving action. It has a C v of 0.4. Sandwich pressure regulator, sandwich speed control, and push-in fittings are available.

NUMATICS

AC and DC output drivers

The SDS Output driver is a device which can be used to control solenoids, motor starters, pilot lights and other remote electrical devices over the SDS bus. AC and DC versions are available; the DC version can obtain its power from the SDS bus.

EXTRON

Serial Manifolds

This new line of SDS-compatible Serial Manifolds (SM) range from miniature to large 2-way, 3-way, and 4-way configurations spanning various flow ranges. Many of the standard valve options such as regulators, flow controls, and 'add-on' style manifolds are available.

MAC VALVES INC.

Communication link for VSD

An interface card allows MagneTek's compact GPD 333 variable-speed ac drive to be connected directly to the SDS network. The GPD 333 is available in ran-ges of 1 to 5 horsepower, 230 or 460 V ac. The SDS network interface for the larger GPD 515 will follow.

MAGNETEK





No comments
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
High-performance buildings; Building envelope and integration; Electrical, HVAC system integration; Smoke control systems; Using BAS for M&V
Pressure piping systems: Designing with ASME; Lab ventilation; Lighting controls; Reduce energy use with VFDs
Smoke control: Designing for proper ventilation; Smart Grid Standard 201P; Commissioning HVAC systems; Boilers and boiler systems
Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Consulting-Specifying Engineer case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.

Protecting standby generators for mission critical facilities; Selecting energy-efficient transformers; Integrating power monitoring systems; Mitigating harmonics in electrical systems
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software
Integrating BAS, electrical systems; Electrical system flexibility; Hospital electrical distribution; Electrical system grounding
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.