Belling the code-and-standard cat

10/01/2009


Why and when did regulations solidify to a point where unbending, homogenized codes and standards keep engineers from exercising their expertise and good judgment?

This situation is particularly true for lighting. Lighting has become the stepchild of construction. It is often the last to be considered in planning, the first to be jettisoned in the budget crunch, mostly assumed to be present but often created without adequate thought, and many times beset by unfathomable limitations.

 

Codes and standards represent only the barest minimum requirements; if they are followed slavishly without imagination and innovation, there will be just minimum results. Owners have been duped into believing that simply meeting codes and standards is good design.

 

However, despite prolific codes and standards, bad lighting is everywhere. It may be too hot, too dim, glaring, or unfocused; lack contrast; have the wrong color/style; or be thoughtlessly installed. Wiring and controls could be faulty. Unauthorized substitutions could drastically alter performance. Maintenance could be inaccessible and disruptive. For example, a light high above an indoor swimming pool—to relamp, the pool must be drained and scaffolding erected.

 

And now we have the added factor of energy conservation mandates through efficiency standards that are being adopted as codes. Being “green,” sustainable, and energy-efficient are not always mutually achievable in lighting because of the range of applications, conditions, and conflicts with other building systems.

 

Commenting on the subject, Larry Spielvogel, PE, consulting engineer, King of Prussia, Pa., and former chairman of the ASHRAE/IESNA/ANSI Standard 90.1 committee , said: “Building codes and standards should set only the minimum acceptable criteria to protect the public health and safety. Unfortunately, they have become the receptacle for requirements proposed by those seeking to feather their nests, further their competitive advantage, or advance their ideology.”

 

Carl Watson, PE, LC, principal, Applied Energy Solutions , Wynnewood, Pa., agrees that arbitrary, unworkable one-size-fits-all rules could “straitjacket” appropriate lighting design. Only if the most energy-efficient lighting technology, best suited for the particular application, is known and used, can sophisticated and affordable illumination be created within the increasing energy restrictions. This is because a careful combination of techniques, both architectural and theatrical, may be necessary to achieve the lighting wish list.

 

Belling the cat

Here are nine recommendations for belling the code-and-standard cat:

 

  1. Most building codes address only new work, ignoring existing structures constructed with earlier methods and materials. This omission creates many problems.

  2. It is not just a question of simply requiring or excluding certain actions. Practical education in why to do something, in addition to prohibitions, is necessary so the public understands the reason for logical parameters.

  3. Buildings are like humans. Location, climate, and use affect them differently. Therefore, extenuating circumstances in lighting codes and standards must be considered in order for illumination to perform safely and effectively.

  4. There should be reasonable universal coordination in regulations, especially when simply crossing the street into another jurisdiction could result in a 180-degree interpretation. As a federal exercise, why not establish a nationwide rejection feature for lamps and bulbs, similar to that for fuses, to eliminate incorrect replacements?

  5. All codes and standards should be written in plain English, readily understandable by everyone, including homeowners, tradesmen, and bankers. Many still call a lighting unit a “fixture,” instead of the artificial term “luminaire,” indicating necessity for a dictionary of lighting terms.

  6. How does one judge what is safe, comfortable, and energy-conserving, unless all the factors are comparable? This is not always possible with lighting because there are so many variables to consider. Demanding sameness of lighting performance is questionable, too. Quoting Spielvogel again, “As one example of codes and standards that do not make common sense, why do they require the same minimum boiler efficiency in Miami as in Minneapolis?” Another example is the uninformed banning of incandescent lamps by politicians who know little about lighting.

  7. Codes and standards should include scheduled maintenance requirements to keep correctly installed lighting from later being dangerously jerry-rigged by careless maintenance. In too many cases, maintenance workers tamper with once-correct lighting, rendering fixtures unsafe or no longer operable.

  8. Require complete truth in advertising. The fanciful claims for some widely publicized lighting products do not disclose all the properties necessary to make the proper selections. In lighting, one size does not fit all, especially concerning sustainability.

  9. Carrots and sticks still are the ultimate solution. Reward excellence with meaningful financial incentives, balanced with stiff penalties for ignoring or avoiding reasonable codes and standards.

 

 

Author Information

Kay is the president and founder of Conservation Lighting International and Building Conservation International in Philadelphia. She is on the board of managers of the Philadelphia Chapter of IESNA, and served four years as an appointed lighting designer on the national ASHRAE/IESNA/ANSI committee on Standard 90.1.



No comments
Consulting-Specifying Engineer's Product of the Year (POY) contest is the premier award for new products in the HVAC, fire, electrical, and...
Consulting-Specifying Engineer magazine is dedicated to encouraging and recognizing the most talented young individuals...
The MEP Giants program lists the top mechanical, electrical, plumbing, and fire protection engineering firms in the United States.
High-performance buildings; Building envelope and integration; Electrical, HVAC system integration; Smoke control systems; Using BAS for M&V
Pressure piping systems: Designing with ASME; Lab ventilation; Lighting controls; Reduce energy use with VFDs
Smoke control: Designing for proper ventilation; Smart Grid Standard 201P; Commissioning HVAC systems; Boilers and boiler systems
Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Consulting-Specifying Engineer case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.

Protecting standby generators for mission critical facilities; Selecting energy-efficient transformers; Integrating power monitoring systems; Mitigating harmonics in electrical systems
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software
Integrating BAS, electrical systems; Electrical system flexibility; Hospital electrical distribution; Electrical system grounding
Cannon Design’s blog is a place for the many voices of the firm to share thoughts and news related to current projects...
As brand protection manager for Eaton’s Electrical Sector, Tom Grace oversees counterfeit awareness...
Amara Rozgus is chief editor and content manager of Consulting-Specifier Engineer magazine.
IEEE power industry experts bring their combined experience in the electrical power industry...
Michael Heinsdorf, P.E., LEED AP, CDT is an Engineering Specification Writer at ARCOM MasterSpec.